Short Pitch Conveyor Chain Attachments
Roller chains may be adapted to conveying applications by the addition of attachments. The standard attachment types include bent or straight-type attachments on one or both sides, extended pins, and wide contour attachments.Standard Roller Chain Attachment: A1, A2, K1, K2, SA1, SA2, SK1, SK2, WA1, WA2, WK1, WK2, D1, D5, GK1.The purpose of using roller chain attachments is to offer a wider range of capabilities for your roller chains. We offer a lot of attachments that can be used with roller chains that are specific to certain special functions. When you couple attachments with roller chains, you’ll find that your roller chains are even more capable of moving heavy equipment while remaining cost-effective, reliable, and sturdy.
Short Pitch Conveyor Chain Attachments
Short Pitch Conveyor Chain Attachments may be adapted to conveying applications by the addition of attachments. The standard attachment types include bent or straight-type attachments on one or both sides, extended pins, and wide contour attachments.Standard Roller Chain Attachment: A1, A2, K1, K2, SA1, SA2, SK1, SK2, WA1, WA2, WK1, WK2, D1, D5, GK1.The purpose of using roller chain attachments is to offer a wider range of capabilities for your roller chains. We offer a lot of attachments that can be used with roller chains that are specific to certain special functions. When you couple attachments with roller chains, you’ll find that your roller chains are even more capable of moving heavy equipment while remaining cost-effective, reliable, and sturdy.
Roller Chain Attachment Types
| (1) Roller Chain with A-1 K-1 Attachment | |
 |
 |
| A-1 | K-1 |
 |
|
| DIN Chain No. | ANSI Chain No. | P | G | F | W | T | h4 | d4 |
| mm | mm | mm | mm | mm | mm | mm | ||
| 08ASS | 40SS | 12.7 | 9.5 | 25.4 | 35.2 | 1.5 | 7.9 | 3.4 |
| 10ASS | 50SS | 15.875 | 12.7 | 31.75 | 46.2 | 2.03 | 10.3 | 5.5 |
| 12ASS | 60SS | 19.05 | 15.9 | 38.1 | 55.6 | 2.42 | 11.9 | 5.5 |
| 16ASS | 80SS | 25.4 | 19.1 | 50.8 | 64.8 | 3.25 | 15.9 | 6.8 |
| 20ASS | 100SS | 31.75 | 25.4 | 63.5 | 87.3 | 4 | 19.8 | 9.2 |
| 24ASS | 120SS | 38.1 | 28.6 | 76.2 | 108.5 | 4.8 | 23 | 9.8 |
| 28ASS | 140SS | 44.45 | 34.9 | 88.9 | 123 | 5.6 | 28.6 | 11.4 |
| 32ASS | 160SS | 50.8 | 38.1 | 101.6 | 142.8 | 6.4 | 31.8 | 13.1 |
| *06BSS | 9.525 | 8 | 19.04 | 27 | 1.3 | 6.5 | 3.5 | |
| 08BSS | 12.7 | 9.5 | 25.4 | 36.4 | 1.6 | 8.9 | 4.5 | |
| 10BSS | 15.875 | 14.3 | 31.75 | 44.6 | 1.7 | 10.31 | 5.3 | |
| 12BSS | 19.05 | 16 | 38.1 | 52.4 | 1.85 | 13.46 | 6.4 | |
| 16BSS | 25.4 | 19.1 | 50.8 | 72.6 | 3.1 | 15.88 | 6.4 |
| (2) Roller Chain with SA Attachment | |
 |
 |
| SA-1/M1(One Side) | SK-1/M1(Two SIde) |
|
|
|
| DIN ISO Chain No. | ANSI Chain No. | P | G | C | F | T | d4 |
| mm | mm | mm | mm | mm | mm | ||
| 08ASS | 40SS | 12.7 | 9.5 | 12.7 | 19.05 | 1.5 | 3.4 |
| 10ASS | 50SS | 15.875 | 12.7 | 15.9 | 25.25 | 2.03 | 5.5 |
| 12ASS | 60SS | 19.05 | 15.9 | 18.3 | 29.33 | 2.42 | 5.5 |
| 16ASS | 80SS | 25.4 | 19.1 | 24.6 | 34.7 | 3.25 | 6.8 |
| 20ASS | 100SS | 31.75 | 25.4 | 31.8 | 43.3 | 4 | 9.2 |
| 24ASS | 120SS | 38.1 | 28.6 | 36.5 | 51.6 | 4.8 | 9.8 |
| 28ASS | 140SS | 44.45 | 34.9 | 44.5 | 62 | 5.6 | 11.4 |
| 32ASS | 160SS | 50.8 | 38.1 | 50.8 | 69.85 | 6.4 | 13.1 |
| *06BSS | 9.525 | 8 | 9.52 | 13.5 | 1.3 | 3.5 | |
| 08BSS | 12.7 | 9.5 | 13.35 | 18.9 | 1.6 | 4.5 | |
| 10BSS | 15.875 | 14.3 | 16.5 | 22.95 | 1.7 | 5.3 | |
| 12BSS | 19.05 | 16 | 21.45 | 28.6 | 1.85 | 6.4 | |
| 16BSS | 25.4 | 19.1 | 23.15 | 34 | 3.1 | 6.4 |
| (3) Roller Chain with WA WK Attachment | |
 |
 |
| WA-1 | WK-1 |
 |
|
| DIN ISO Chain No. | ANSI Chain No. | P | G | L | F | W | T | h4 | d4 |
| mm | mm | mm | mm | mm | mm | mm | mm | ||
| 08ASS | 40SS | 12.7 | 23 | 12.7 | 25.4 | 35.6 | 1.5 | 7.9 | 3.4 |
| 10ASS | 50SS | 15.875 | 28.8 | 15.875 | 31.8 | 46.8 | 2.03 | 10.3 | 5.5 |
| 12ASS | 60SS | 19.05 | 34.65 | 19.05 | 38.1 | 56.4 | 2.42 | 11.9 | 5.5 |
| 16ASS | 80SS | 25.4 | 45.9 | 25.4 | 50.8 | 73.2 | 3.25 | 15.9 | 6.8 |
| 20ASS | 100SS | 31.75 | 57.65 | 31.75 | 63.5 | 89.8 | 4 | 19.8 | 9.2 |
| 08BSS | 12.7 | 24 | 12.7 | 25.4 | 36.4 | 1.6 | 8.9 | 4.3 | |
| 10BSS | 15.875 | 29.58 | 15.875 | 31.8 | 44.6 | 1.7 | 10.31 | 5.3 | |
| 12BSS | 19.05 | 34.05 | 19.05 | 38.1 | 52.4 | 1.85 | 13.46 | 6.4 | |
| 16BSS | 25.4 | 46.4 | 25.4 | 50.8 | 72.6 | 3.1 | 15.88 | 6.4 |
| (4) Roller Chain with WSA WSK Attachment | |
 |
 |
| WSA-1 | WSK-1 |
 |
|
| DIN ISO Chain No. | ANSI Chain No. | P | G | L | C | F | T | d4 |
| mm | mm | mm | mm | mm | mm | mm | ||
| 08ASS | 40SS | 12.7 | 23 | 12.7 | 12.7 | 17.4 | 1.5 | 3.4 |
| 10ASS | 50SS | 15.875 | 28.8 | 15.875 | 15.9 | 23.05 | 2.03 | 5.5 |
| 12ASS | 60SS | 19.05 | 34.65 | 19.05 | 18.3 | 28.86 | 2.42 | 5.5 |
| 16ASS | 80SS | 25.4 | 45.9 | 25.4 | 24.6 | 35.45 | 3.25 | 6.8 |
| 20ASS | 100SS | 31.75 | 57.65 | 31.75 | 31.8 | 44 | 4 | 9.2 |
| 08BSS | 12.7 | 23.3 | 12.7 | 13.35 | 18.9 | 1.6 | 4.5 | |
| 10BSS | 15.875 | 29.58 | 15.875 | 16.5 | 22.95 | 1.7 | 5.3 | |
| 12BSS | 19.05 | 34.05 | 19.05 | 21.45 | 28.6 | 1.85 | 6.4 | |
| 16BSS | 25.4 | 46.4 | 25.4 | 23.15 | 34 | 3.1 | 6.4 |
| (5) Roller Chain with D-1 Attachment | |
 |
 |
| DIN ISO Chain No. | ANSI Chain No. | P | b2 | d2 | L3 | L | Lc |
| mm | mm | mm | mm | mm | mm | ||
| 06CSS | 35SS | 9.525 | 4.77 | 3.58 | 9.5 | 20.8 | 21.6 |
| 08ASS | 40SS | 12.7 | 7.85 | 3.96 | 9.5 | 25.1 | 26.2 |
| 10ASS | 50SS | 15.875 | 9.4 | 5.08 | 11.9 | 31.3 | 33.1 |
| 12ASS | 60SS | 19.05 | 12.57 | 5.94 | 14.3 | 38.6 | 40.6 |
| 16ASS | 80SS | 25.4 | 15.75 | 7.92 | 19.1 | 50.3 | 53.3 |
| 20ASS | 100SS | 31.75 | 18.9 | 9.53 | 23.8 | 61.8 | 66.1 |
| 24ASS | 120SS | 38.1 | 25.22 | 11.1 | 28.6 | 76.4 | 80.4 |
| 28ASS | 140SS | 44.45 | 25.22 | 12.7 | 33.3 | 84.8 | 89.4 |
| 32ASS | 160SS | 50.8 | 31.55 | 14.27 | 38.1 | 99.6 | 104.4 |
| 08BSS | 12.7 | 7.75 | 4.45 | 9.5 | 25.1 | 26.6 | |
| 10BSS | 15.875 | 9.65 | 5.08 | 11.9 | 30.1 | 31.5 | |
| 12BSS | 19.05 | 11.68 | 5.72 | 14.3 | 35.4 | 37.1 | |
| 16BSS | 25.4 | 17.02 | 8.28 | 19.1 | 53 | 54.3 |
Roller Chain Attachments Features
- A1/A2, K1/K2, SA1/SA2, and SK1/SK2 style attachments
- Heat-treated and shot-peened components
- Solid bushings and rollers for carbon steel
- Stainless steel / Carbon steel with a corrosion-resistant coating is available.
- Matched and tagged available
- Custom design attachments at request
What is Roller Chain Pitch?
The size of a chain is determined by three measurements: pitch, gauge and drive link count. Roller chain pitch is the distance between three rivets divided by two. Gauge is the thickness of the drive links where they connect to form a loop. Drive link count refers to how many drive links are in a chain loop. The drive sprocket must be the same pitch as the chain, and if applicable, the bar nose sprocket must also match.
How Do You Attach a Roller Chain?
For starters, you’re going to need an angle grinder, either a chain or punch screw, chain vise and either a level, straight edge or laser alignment piece of equipment. For the first step, you’ll take the riveted part of the two pins and grind them with the grinder, removing any cotter pins if you have to. Then, make sure the chain is secure in the vise. Use the secondary and primary punches and remove one of the pin sets. For step three, check both the parallel shaft and sprocket axial alignments using either the level, straight edge or laser tool. A misaligned chain will hold uneven loads across its width, resulting in uneven wear on roller link plates and sprockets. Sprockets should be placed as close as possible to bearings. Then you’ll install both chain ends to the sprocket and link them together and fasten them with cotters or a spring clip (you might need some help to support the chain).
Common Applications For Attachment Roller Chain
- Round bottom drag conveyors
- Combines
- Bakery equipment
- Lumber Conveyors
- Printing & Labeling Machines
- Automation equipment
- Car manufacturing assembly lines
- PPE manufacturing equipment
Related Products
 |
 |
 |
| Automobile chains | Drive chains | Conveyor chains |
 |
 |
 |
| Engineering chains | Traction chains | Agricultural machinery chains |
 |
 |
 |
| Stainless steel chains | Escalator chains | Chain wheel |
We Also Provide Sprockets to Match Your Roller Chains
Packaging Display of Roller Chains
Our chain is most commonly supplied in 10ft boxes, including one connecting link per box, but we can also supply this chain at custom lengths as needed. We also offer a full line of good-quality sprockets for this chain. For pricing and availability, please contact us at any time.
Production Workshop of Roller Chains
Our company is an industry-leading, reliable and outstanding roller chain supplier that aims to provide high-quality products at more competitive prices and better service. We have a full line of premium quality stainless steel roller chain attachments in stock. We have ANSI #25 – #80 attachments, double-pitch stainless steel roller chain attachments, and metric roller chain attachments. Typically we stock these attachments in 304-grade stainless steel, but 316-grade is available upon request. We can also supply stainless steel roller chains with stainless steel attachments already assembled onto the chain; just allow a few days for assembly. To get a quote or for more information, please contact us, and we will be happy to assist you.
- Good quality products at competitive pricing
- Wide variety of products available in various materials and sizes
- ISO9001-certified factory
- Great customer service that’s here to answer all of your questions
- Largest online selection of power transmission products
- Easy online shopping and ordering available 24/7 – 365 days a year
- High quality made to order products
Packing Shipping Delivery
  |
 |
|
 |
 |
|
How to choose power transmissions parts and industrial products which meet our requirement
| Chains | Sprockets | Pulleys | Timing belt Pulley | V-belt Pulley |
| Sheaves | Coupings | Bush &Hub | Gear& Rack | V-Belt |
| Locking Assembly | Pulley | Gearbox | Reducer | Shaft Collar |
| Rod End Bearing | Clevis | PTO | Chain Guide | Belt Guide |
| Rubber Buffer | Chain Tensioner | PTO Drive Shafts | Universal Joints | Roller Chains |
| Conveyor Chains | V-Belts | Worm Gearbox | Helical Gear | Worm |
| Agricultural Chain | CNC Proces Parts | Casting | Stamping | |
| Powder Metallurgy | CNC Proces Parts | Casting | Stamping |
What Products Do you sell ?
We are a group of factories, give customer one stop solution of power transmission and industrial products. We are in the position to supply wide range of products, including chains, sprockets, v-belt and v-belt pulleys, timing belt and timing belt pulleys, gears, speed reducers, motors, racks, couplings, and many other parts, like locking assembly, taper bushing, Chain guide, shaft collar, torque limiter, cam clutch, universal joint, motor base and motor slide, rod end, clevis, rubber mount, etc. We make special parts according to drawings and/or samples.
How to choose a gearbox which meets our requirement?
You can refer to our catalogue to choose the gearbox or we can help to choose when you provide
the technical information of required output torque, output speed and motor parameter etc.
What information shall we give before placing a purchase order?
a) Type of the gearbox, ratio, input and output type, input flange, mounting position, and motor informationetc.
b) Housing color.
c) Purchase quantity.
d) Other special requirements.
What industries are your gearboxes being used?
Our gearboxes are widely used in the areas of textile, food processing, beverage, chemical industry,
escalator,automatic storage equipment, metallurgy, tabacco, environmental protection, logistics and etc.
What is the producing process?
Production process including raw material cutting, machine processing, grinding, accessories cleaning, assemble, cleaning, stoving, oil coating, cover pressing, testing, package.
How to control the products quality?
Combining advanced equipment and strict management, we provide high standard and quality bearings for our customers all over the world.
What is the transportation?
-If small quantity , we Suggest to send by express, such as DHL,UPS, TNT FEDEX. If large amount, by air or sea shipping.
Can we design packaging?
-Yes. Default is regular packing, and we can make customer's own packing.
Can you provide OEM service?
-Yes, we work on OEM orders. Which means size, quantity, design, packing solution, etc will depend on your requests; and your logo will be customized on our products.
Can you give me discount on Power Transmissions Parts and Industrial parts?
-Yes, of course. Pls. send me your Email, you'll get more
Q: Are You a trading company or a manufacturer?
A: We Are the factory and have our Own trading company
Q: How Can I get an offer?
A: please send US quotation information: drawings, materials, weight, quantity and requirements, we can accept PDF, ISGS, DWG, STEP file format. If you don't have the drawings, please send us the samples, we can also quote you according to your samples.
Q: What is your minimum order size?
A: it is usually 100 pieces, but a low quantity is acceptable under some special circumstances.
Q: Do you provide samples? Is it free or extra?
A: Yes, we can provide samples free of charge, but we don't pay the freight.
Q: What is the lead time for mass production?
A: honestly, it depends on the number of orders. Normally, if you don't need the tools, deposit them after 30 days or so.
Q: What if the parts don't Work?
A: we can guarantee the quality, but if it happens, please contact us immediately, take some photos, we will check the problem and solve it as soon as possible.
Q: What are your terms of payment?
A: payment is less than US $1000,100% in advance. Payment: $1000,50% wire transfer in advance, balance before shipment,Other Terms of payment are negotiable
Reviews
There are no reviews yet.