Short Pitch Conveyor Chain Attachments A-1 K-1
Short Pitch Conveyor Chain Pitch is typically referred to as the distance between links in a conveyor chain, measured From the centre of the roller pin on one link to the centre of the roller pin on the following link.
Short Pitch Conveyor Chain Attachments A-1 K-1
Short Pitch Conveyor Chain Pitch(Short Pitch Conveyor Chain Attachments A-1 K-1) is typically referred to as the distance between links in a conveyor chain. Measured From the centre of the roller pin on one link to the centre of the roller pin on the following link. Be aware that some Precision link conveyors refer to link size as pitch. Chain pitch, which determines the length of the chain, is calculated by Dividing the distance between any three consecutive rivets by two. Our chain with a variety of pitches; the Smallest is 1/4″, the most common is 3/8″, and the largest is 3/4″. You must measure the distance between any three Consecutive rivets to determine the pitch (chain size), then divide the result by two.
Our company also provides many conveyor chain types. If you need to know more product types and information, such as conveyor chain, you can contact us by email or communicate with our online staff. Looking forward to working with you.
 |
 |
 |
 |
 |
 |
Sprockets for Short Pitch Conveyor Chain
Before installing sprockets, it is important to check the centerline of the roller chain drive. The centerline can be horizontal or vertical but should not exceed 60 degrees. Otherwise, the roller chain may slip off the sprocket due to slight elongation. To correct this, use an idler pulley or guide block. Also, remember to adjust the center-to-center distance of the sprockets if the travel distance is short.
A properly designed sprocket will prolong the life of the chain. If the chain fails to engage the sprockets, it usually needs to replace. Proper selection of the right chain will ensure a long service life and prevent damage or premature wear. While various sprockets are available for different chains, design the products to fit the chain perfectly.
| One-stop Supplier of Chain Transmission Products | |||
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
Related sprockets
Q & A
Q: What is the strength of your company? A: We have an engineering team who have well experience in products and machine designs. We can help you to solve the problem you meet. Q: How about your quality? A: We have our own professional factory and worker, so believe that our products have an advantage over our competitors. Q: What is your MOQ? A: Minimum order quality is one piece. Q: Could you produce a customized product according to your drawing or sample? A: Yes. We have abundant experience in the production of non-standard products.
Packing Shipping Delivery
  |
 |
|
 |
 |
|
How to choose power transmissions parts and industrial products which meet our requirement
| Chains | Sprockets | Pulleys | Timing belt Pulley | V-belt Pulley |
| Sheaves | Coupings | Bush &Hub | Gear& Rack | V-Belt |
| Locking Assembly | Pulley | Gearbox | Reducer | Shaft Collar |
| Rod End Bearing | Clevis | PTO | Chain Guide | Belt Guide |
| Rubber Buffer | Chain Tensioner | PTO Drive Shafts | Universal Joints | Roller Chains |
| Conveyor Chains | V-Belts | Worm Gearbox | Helical Gear | Worm |
| Agricultural Chain | CNC Proces Parts | Casting | Stamping | |
| Powder Metallurgy | CNC Proces Parts | Casting | Stamping |
What Products Do you sell ?
We are a group of factories, give customer one stop solution of power transmission and industrial products. We are in the position to supply wide range of products, including chains, sprockets, v-belt and v-belt pulleys, timing belt and timing belt pulleys, gears, speed reducers, motors, racks, couplings, and many other parts, like locking assembly, taper bushing, Chain guide, shaft collar, torque limiter, cam clutch, universal joint, motor base and motor slide, rod end, clevis, rubber mount, etc. We make special parts according to drawings and/or samples.
How to choose a gearbox which meets our requirement?
You can refer to our catalogue to choose the gearbox or we can help to choose when you provide
the technical information of required output torque, output speed and motor parameter etc.
What information shall we give before placing a purchase order?
a) Type of the gearbox, ratio, input and output type, input flange, mounting position, and motor informationetc.
b) Housing color.
c) Purchase quantity.
d) Other special requirements.
What industries are your gearboxes being used?
Our gearboxes are widely used in the areas of textile, food processing, beverage, chemical industry,
escalator,automatic storage equipment, metallurgy, tabacco, environmental protection, logistics and etc.
What is the producing process?
Production process including raw material cutting, machine processing, grinding, accessories cleaning, assemble, cleaning, stoving, oil coating, cover pressing, testing, package.
How to control the products quality?
Combining advanced equipment and strict management, we provide high standard and quality bearings for our customers all over the world.
What is the transportation?
-If small quantity , we Suggest to send by express, such as DHL,UPS, TNT FEDEX. If large amount, by air or sea shipping.
Can we design packaging?
-Yes. Default is regular packing, and we can make customer's own packing.
Can you provide OEM service?
-Yes, we work on OEM orders. Which means size, quantity, design, packing solution, etc will depend on your requests; and your logo will be customized on our products.
Can you give me discount on Power Transmissions Parts and Industrial parts?
-Yes, of course. Pls. send me your Email, you'll get more
Q: Are You a trading company or a manufacturer?
A: We Are the factory and have our Own trading company
Q: How Can I get an offer?
A: please send US quotation information: drawings, materials, weight, quantity and requirements, we can accept PDF, ISGS, DWG, STEP file format. If you don't have the drawings, please send us the samples, we can also quote you according to your samples.
Q: What is your minimum order size?
A: it is usually 100 pieces, but a low quantity is acceptable under some special circumstances.
Q: Do you provide samples? Is it free or extra?
A: Yes, we can provide samples free of charge, but we don't pay the freight.
Q: What is the lead time for mass production?
A: honestly, it depends on the number of orders. Normally, if you don't need the tools, deposit them after 30 days or so.
Q: What if the parts don't Work?
A: we can guarantee the quality, but if it happens, please contact us immediately, take some photos, we will check the problem and solve it as soon as possible.
Q: What are your terms of payment?
A: payment is less than US $1000,100% in advance. Payment: $1000,50% wire transfer in advance, balance before shipment,Other Terms of payment are negotiable
Reviews
There are no reviews yet.